Swap The Suspect Distributor Ignition Coils To Another Cylinder

  •   How to Test an Ignition Coil on a Modern Car: 6 Different Methods

      Professionals often use the term coil pack to describe any type of modern ignition coil. But, by definition, a coil pack is a group of ignition coils combined together in a single molded block. With this design, each cylinder gets its own ignition tower but shares its coil with a companion cylinder.

      This is different than the more commonly used coil-on-plug (COP) ignition system. In a COP system, each cylinder gets its own Pencil Ignition Coils that sits on top of the spark plug.

      For the sake of convenience, however, we’ll refer to both designs as ignition coils in this article.

      Note: We will not be covering distributor-style ignition systems that use just one coil.

      Although testing ignition coils can be tricky, it’s doable if you have the tools and knowledge. Here are six different methods that will help you get the job done.

      Perform a Visual Inspection

      In some cases, you’ll be able to spot a bad ignition coil with a simple visual inspection. Issues, such as cracks, burn marks, and carbon tracking, point to a faulty coil.

      Swap the Suspect Ignition Coil to Another Cylinder

      If your car has individual ignition coils (or packs that combine just two coils), you can swap the suspect ignition coil to another cylinder to see if the misfire follows.

      But wait—what if you don’t have a scan tool or code reader? In many cases, you can perform a power balance test to cancel out each cylinder. You’ll want to listen for a drop in RPMs as each cylinder is cut out. A cylinder that demonstrates little to no change in RPMs is problematic and not contributing fully.

      Keep in mind: A drop in RPMs on a specific cylinder can be caused by other issues (i.e., fuel delivery or engine mechanical problems) besides a bad coil. To verify whether the coil is to blame, you’ll want to swap the coil to another cylinder and repeat the power balance test. If the loss of contribution moves with the coil, the ignition coil is faulty.

      Caution: Never perform a power balance test by disconnecting the spark plug wires. Damage to the vehicle and severe injury may result.

      Use a Spark Tester

      You can also test an ignition coil with a spark tester. The tool is installed inline with the ignition coil to determine if the coil is producing a spark.

      Note: If all of the ignition coils aren’t delivering spark, the issue is likely with the control side (primary side) of the ignition system, rather than a single ignition coil. An absence of spark from just ONE ignition coil points to a bad coil.

      Not all spark testers work with all types of ignition systems, so be sure to select the right tool for your application. It’s also a good idea to get a quality, adjustable spark tester. Inexpensive non-adjustable testers can be misleading because sometimes they still illuminate with a weak spark.

      The steps for using a spark tester will vary, depending on the tool you’re using and the type of ignition system your car has. But the following video will give you an idea of what’s involved:

      You may hear some people recommend removing the spark plug and grounding it instead of using a spark tester. The issue is, it takes less voltage to fire a spark plug that has been removed from the engine than one that’s still installed.

      So, although you may have spark, it may not be adequate to jump the plug gap with the engine running.

      A quality spark tester, on the other hand, requires tens of thousands of volts to fire. Because of this, the tool provides an accurate measurement of whether there’s enough spark to jump the plug gap.

      Plus, using a spark tester is safer than grounding a plug.

      Use a Coil-on-Plug (COP) Probe

      A coil-on-plug (COP) probe is a tool that uses a phenomenon called magnetic induction to give a clear indication of whether a COP coil is firing. Some COP probes simply flash a light to indicate the coil is working, while others display data on a screen.

      Using a COP probe is easy. Simply follow the product instructions regarding set up, then place the paddle end of the tool over the coil. In the case of a flashing-style probe, the tool will illuminate if the coil is firing.

        We also provide products such as Auto Ignition Coil, Please don't hesitate to contact us.